Next start up WSJT-X, and Select File Settings and click on the radio tab. Please note that near the beginning of April 20218, there were new Rig Definitions available for Omni-Rig that correct a number of errors. The other options should by default look as above. Select the Rig type, the Port which in this case is Com16 from the Com16 – Com17 pair defined in COM0COM above and the baud rate. This can be located by using the search menu in Windows. So for WSJT-X, use only Radio 1 in Omni-Rig. Unfortunately, WSJT-X has a bug where Omni-Rig Radio 2, when selected, still uses the definitions for Radio 1. Omni-Rig supports two radios, Radio 1 and Radio 2. As always make sure you create the pair when both applications are closed otherwise they will not see the comports.įor WSJT-X, you must use Omni-Rig. The following is a screen shot of the following: A com0com pair that was created (com19 and com20), a connection in Win4Icom’s Settings, 3rd party Software, and the settings in FLDigi. Search Google for RigCat IC-7610 or What ever rig you need. FLDigiįor FLDigi you will need to create a pair as above and then connect FLDigi using RigCat. You can use the same principle for any other third party software such as N1MM, DX4Win and so on. Therefore everything that is supported in DXLabs Suite also works. From the point of view of DXCommander, all it sees is a Icom radio connected to its comport. Next click on the Ports tab and enter Port# 16 corresponding to the serial port of the virtual comport pair you created above.Įxit out and you should be connected to DXCommander. Select Config from the main DXCommander screen: Third Party Software Setup DX CommanderĪs an example, DXCommander from DXLab Suite is configured as follows. Please note that while these work, none seem to be as stable as COM0COM.ĭTR and RTS: Win4IcomSuite does not support the use of DTR or RTS through it’s virtual port facility. There are other packages available that create virtual comport pairs such as one from Eltima ($$) and VSPE. If you wish to connect a hardware device to your system such as an antenna tuner that supports the, just plug it into an available serial port on your computer and enter that comport number in one of the AUX/CAT ports. This has effectively connected the two products together via a null modem cable. The others are currently to other virtual port pairs.Īll you need to do now is save the settings and then configure your third party product to connect to comport 16 which is the second comport of the COM17-COM16 pair. In this example, AUX/CAT Port 1 is connected to comport 17. Each one can connect to a comport of a virtual comport pair. In this screen there are 6 AUX/CAT ports. Once the comport pair is created, start up Win4IcomSuite and select Tools, Settings, and the 3rd Party SW/HW tab. In the above I created several pairs Please note that many older software packages may not know about comports with numbers higher than COM9. You can just click on the names and change the names of the comports to a comport name that does not exist on your system. There will be by default one pair already defined with weird letter names. Many of them DO NOT work correctly.Īfter you install this, open the Windows start menu and in the com0com folder run “Setup.” (Don’t run Setup Command line). If you do this, contact support for how to fix the errors (for those in the know, use the device manager and delete the driver file, then reinstall).ĭo not use other products. If you download a newer version that is NOT signed you will have many errors even if you uninstall it and then try to install this version. The recommended utility which is free, is COM0COM which is open source and available at:īe sure to use the signed version for your operating system. In order to use this feature you will need to download a third party utility that provides virtual serial port pairs that act as cables between two software products in Windows. These ports provide an interface that for all purposes look just like an Icom to the third party product. Win4IcomSuite supports many third party products by providing 6 auxiliary ports that accept CI-V commands. Click here for Ham Radio Deluxe Logbook and DM780 integration.Įxamples in this page are for DXLab, WSJT-X and FLDigi. Please note: You do not need this for Ham Radio Deluxe Logbook and DM780. Please take a few minutes to understand the concept below. Win4IcomSuite has a robust and trouble free comport sharing mechanism built in.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |